If anyone is interested in helping create a new site logo please email webmaster@allworxforums.com
PLEASE NOTE: Allworxforums.com is not owned, nor run by Allworx Corp. The views and opinions found on this forum are not necessarily the views of Allworx or the forum moderators. Neither Allworx nor the forum will be held liable for any information found on the forum. The Allworx logo and name is a registered trademark of Allworx Corp.
PLEASE NOTE: Allworxforums.com is not owned, nor run by Allworx Corp. The views and opinions found on this forum are not necessarily the views of Allworx or the forum moderators. Neither Allworx nor the forum will be held liable for any information found on the forum. The Allworx logo and name is a registered trademark of Allworx Corp.
Search found 109 matches
- Wed Jun 26, 2013 12:25 pm
- Forum: Installation and Configuration Help
- Topic: Handset Paging on Allworx 9212L?
- Replies: 6
- Views: 6519
Re: Handset Paging on Allworx 9212L?
Are the sets all on the same network as the Allworx server? Allworx paging uses Multicast broadcaster - perhaps it is being blocked by a switch or router on your network? I had to have our network group setup some specific rules to pass the paging to remote WAN sites. Didn't have to change anything ...
- Wed Jun 26, 2013 12:22 pm
- Forum: Installation and Configuration Help
- Topic: Remote Phone Registration Error
- Replies: 4
- Views: 16110
Re: Remote Phone Registration Error
Do you or someone at your office have access to the Allworx 6x configuration? You would access it at http://<ip of 6x>:8080 Check the Network Configuration - I'm going to assume it is probably in LAN Host mode. Take a look at the Public IP Address setting - does it match the current Public IP addres...
- Tue Jun 25, 2013 9:09 pm
- Forum: Installation and Configuration Help
- Topic: Remote Phone Registration Error
- Replies: 4
- Views: 16110
Re: Remote Phone Registration Error
When you say that the office rebooted its modem, did they just turn it off and back on again? Or did they factory reset it or something more drastic like that? The first place to check would be with your office firewall, especially if nothing changed at your home. Was it the company that no longer s...
- Tue Jun 25, 2013 9:01 pm
- Forum: Installation and Configuration Help
- Topic: Polycom IP 5000 help!
- Replies: 6
- Views: 11636
Re: Polycom IP 5000 help!
On the Allworx Handsets page, click on the Modify link beside the Generic Handset you setup. What does the Binding show now? I just put in exactly what showed up there for the Address - it had 0.0.0.0 as the IP since nothing had connected... Looking at it now, it is showing the IP address that the I...
- Fri Jun 21, 2013 7:49 am
- Forum: Allworx Software Support
- Topic: iAllworx and voicemail forwarding
- Replies: 1
- Views: 3450
Re: iAllworx and voicemail forwarding
Try using Allworx Reach instead. I guess you'll have to be on v7.5 for that to work.
You don't need to use a Reach license for all the same VM functionality that iAllworx has.
I haven't tested myself, but it's worth a shot if it will work for you.
You don't need to use a Reach license for all the same VM functionality that iAllworx has.
I haven't tested myself, but it's worth a shot if it will work for you.
- Wed Jun 19, 2013 7:30 pm
- Forum: Allworx Software Support
- Topic: Current Builds List
- Replies: 23
- Views: 237586
Re: Current Builds List
7.5.5.5
- Mon Jun 17, 2013 10:55 am
- Forum: Installation and Configuration Help
- Topic: Polycom 6000 IP Soundstation and Allworx 6X
- Replies: 1
- Views: 2896
- Mon Jun 17, 2013 10:50 am
- Forum: Off-Topic
- Topic: Block incoming phone numbers
- Replies: 3
- Views: 25009
Re: Block incoming phone numbers
You can control this on a per Extension basis.
Go to the users Extension that is having the problem. Add new Call Route.
You will be presented with the option of putting in your problem number and can set it to just hang up if calls are received from it.
Go to the users Extension that is having the problem. Add new Call Route.
You will be presented with the option of putting in your problem number and can set it to just hang up if calls are received from it.
- Mon Jun 10, 2013 9:41 pm
- Forum: Allworx Enhancement Requests
- Topic: Release Notes available to end-users
- Replies: 3
- Views: 14683
Re: Release Notes available to end-users
Release notes are now available on the Update page - but only when an update is available. This needs to be changed so that the current release notes can always be accessed, even if there is no update available. Example - I want to go back and review the release notes again but I've already updated....
- Mon Jun 10, 2013 7:02 am
- Forum: Allworx Software Support
- Topic: Current Builds List
- Replies: 23
- Views: 237586
Re: Current Builds List
7.5.4.10
Release Notes are now available direct from the Update page.
Release Notes are now available direct from the Update page.